Plumbing for Beginners: What You Need for Bathtub Installation
Plumbing for Beginners: What You Need for Bathtub Installation
Blog Article
This great article which follows about Tools You Need to Install a New Bathtub is particularly engaging. Don't miss out on it.
Setting up a bath tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is conveniently accessible, the task can move speedily; if you have to open a wall to get rid of the old tub and position the new tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. See to it you have qualified yourself for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you may need a professional plumber to make tube links.
This article will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a new bathtub and do not need to change the plan of your previous supply of water pipelines.
Your tools and material list must comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the restricted gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former type must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bathtub till the spirit level reads level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water and also check all joints and brand-new pipework for leaks and also tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the tub should wait till the bath tub has been made use of a minimum of once as this will certainly settle it into its last placement.
Planning for the Setup
To start with, the sustaining frame supplied with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can fracture rather early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that editorial about Installing A Bathtub through an associate on our other website. Are you aware of somebody who is in to Installing A Bathtub? Feel free to share it. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book 24/7 Report this page